金凤凰彩票app下载

全国咨询热线

行业新闻

济南玻璃隔断应该注意哪些问题?

来源:http://www.wshdgj.com 日期:2020-06-11 发布人:admin
  据玻璃隔断生产厂家介绍玻璃隔断在安装时一般要求比较严格,应做到以下几点要求。
  According to the introduction of the glass partition manufacturer, the general requirements for the installation of the glass partition are relatively strict, and the following requirements shall be met.
  ,上下门轴0须在一个垂,玻璃门0须采用钢结构的横梁做骨架,上轴0须焊接在横梁上,因为轴是整个玻璃门的支撑点,0须要牢g,禁止采用上部横梁采用细木板木结构,因为轴与木制作结构连接点只能使用自攻螺丝固定连接,由于开门次数多,时间长了使轴容易脱落,造成危险。
  The upper and lower door shafts 0 must be in a vertical position. The glass door 0 must be framed by a steel beam, and the upper shaft 0 must be welded on the beam, because the shaft is the supporting point of the whole glass door, 0 must be firm g. it is forbidden to use the upper beam with a thin wood plate structure, because the connection point of the shaft and the wood structure can only be fixed and connected with self tapping screws, because the door is opened many times and the time is long, the shaft is easy to fall off Falling, causing danger.
                  济南玻璃隔断
  济南玻璃隔断
  Jinan glass partition
  第二,预埋地弹簧时要在原地面剔凿一个长方形方坑,四周要大于地弹簧底座的10毫米,用于塞实高标水泥砂浆,起到牢g的作用,建议地弹簧水泥凝固48小时后按照玻璃门,安装好玻璃门地边要距地8-12毫米,玻璃门在下垂的时候摩擦地面。
  Second, when pre burying the spring, a rectangular square pit shall be chiseled on the original ground, and the surrounding area shall be 10 mm larger than the base of the ground spring. It is used to plug the high-grade cement mortar, which plays a role of fixing g. it is recommended that the ground edge of the glass door shall be 8-12 mm away from the ground according to the glass door 48 hours after setting. When the glass door is sagging, it will rub the ground.
  第三,弹门的上下门轴要座于门框的,使玻璃门安装好以后也能座于门框的,起到美观的,还有一个细节问题要注意,门轴与门夹的部位要注入黄油,可以减少连接件的磨损,以使用寿命。
  Third, the upper and lower door shafts of the spring door should be located in the center of the door frame, so that the glass door can also be located in the center of the door frame after installation, which is beautiful. There is also a detail problem to be noted that the parts of the door shaft and the door clamp should be injected with butter, which can reduce the wear of the connecting parts, so as to use life.

上一篇:玻璃隔断应该如何选购呢?
下一篇:玻璃隔断的构造做法和节点绘制形式

金誉彩票app 鑫彩网彩票APP 欢乐彩票app 幸运彩票app 98彩票app下载 苹果彩票app 永盛彩票注册 新世佳彩票APP 58彩票网 永盛彩票注册